The size of this steel table was perfect for my needs, I got two. Previous experience assembling furniture that comes in a box can vary according to the outcome of the experiences. It can be very frustrating when directions are missing or non-existent. The latter in this case but being armed with the right tools can make all the difference in ease of assembly. A second pair of helping hands can be invaluable, but working solo can be made easier. Laying the top flat on a bench allows free access to screw holes. A rubber hammer is a must for assembling most furniture. The legs of this table needed to be attached first, it took two good whacks with the dum-dum hammer, but they went in smoothly lined up with the screw holes and placement was easy. The second item that helps with remaining shelves is something to peg into the holes where the screws will be placed. Hold the shelf in place and slide the pegs through the shelf hole lined up with the chosen leg hole. This is a very short-term aid so use whatever is most accessible at hand. I used 8-penny nails with the first table, I used old small Allen wrenches for the second, but toothpicks, matchsticks, kabob sticks, or whatever you might have nearby will handy temporary pegs. The nail heads that I used kept the shelf very loosely but in place until I got the first screw started then did the opposite corner. The small Allen wrenches did better. And as advised in other reviews, don't ever completely tighten screws but do get them at least 75% set so that the shelves line up well until assembly is complete and final tightening of all screws can be done. I did have more trouble with the middle shelf (put in first) on the second table, I had to loosen the screws on the top shelf to get the first screw/washer into the first hole. Be sure to do a final tightening, you might have a wobbly table if only one screw is loose.

Genial acero inoxidable

Very good quality and ease of assembly.

It's nice does the job

Does a nice job.,

I recently acquired the VIVOHOME Outdoor 3-Burner Stove for an event in downtown Toronto, and I must admit, it exceeded my expectations in both functionality and ease of use.One of the standout features of this stove is its impressive BTU output. The stove reaches up to 225,000 BTU/hr, providing powerful heat that made cooking large quantities of food both quick and efficient. This high heat capability was perfect for the demands of a busy event, allowing us to serve guests without any significant wait times.Additionally, the design of the stove is well-thought-out, particularly in terms of ergonomics. The height of the stove is ideal, creating a comfortable cooking environment that didn’t require any bending or awkward positioning. This design consideration made it much easier to manage multiple dishes simultaneously, which is often a challenge with less thoughtfully designed outdoor stoves.Maintenance and cleanup were also straightforward, thanks to the stove’s heavy-duty construction and quality materials. It held up well throughout the event and was easy to clean afterward, which is a huge plus when dealing with outdoor cooking equipment.

Arrived quickly. Nice and big. All connections look good

I first thought it wouldn’t be a good table because of the price but it turned out to be a great table no complaints

Table is as described, easy to assemble for the most part. It is sturdy and looks good.

I bought the small 18"x24" size table with wheels to use as a microwave cart. It looks really strong, but the design has some issues: the legs are in 2 sections and will come apart if the cart is picked up to move over a threshold. The table surface isn't very solid either.

Used this table for my 1/2hp 60 lb meat slicer. After a couple years of using it once a week, the metal legs were leaning and wanted to break off. Replaced with regency 18-gauge type 304 stainless steel table for about $80 more and it's much more durable. New table feels like it can last a lifetime. I paid not too much for this table and got a couple years out of it

Solid construction and materials, it is made to last while looking like it came out of a professional kitchen. Easy to assemble if you have basic skills and logical thinking. Granted, it didn't come with any reasonable instructions as noted by other reviews and the vendor should make a serious effort to rectify that. I took my time and started with top upside down on the counter and added each piece slowly and even had to change a few times to get it to come out right. I agree it was a little frustrating, but came out great in the end. One suggestion on attaching the screws, do NOT overtighten them, snug them down a little as you go and tighten EVERY screw individually when fully assembled and you have a table that will outlast you while looking great. The negative here is the plastic coating/shield on the surfaces are a bi%$ch to remove. It can be done, but you must have patience, lots & lots of patience and you have to go verry verry slow..

The table is okay but the metal isn't very thick. Had one bolt that didn't have the center hole in the head.

We purchased this cart to use in conjunction with our outdoor pizza oven. It has locking wheels and has a nice surface to work on. It is sturdy, but lightweight. It is a good value for your money, and very attractive.

I live in a 100(+) year old house with a kitchen that just does not have much flat working surfaces. The kitchen is big by today's standards so there was a lot of open space in the middle of the room. I looked in Home Stores, Bulk Big Box Stores, and Kitchen Supply for a work table I could use as a center island and workspace in my kitchen. I could find nothing that satisfied my need. The problem is all the stores have a very limited variety because of sales space. I went to Amazon and saw a vast number of offerings. I was able to scroll and then there this table was. The perfect size. It sits in the middle of the kitchen with plenty of surrounding room for sink, stove, breakfast table and storage chest. To top it off it is made of 100% Stainless Steel. It arrived boxed. The assemble was simple and involved just a few steps. One extra nice feature is the leveling feet that adjusted for a level work surface on my slightly sloping 100 year old pine flooring. Nice gauge of metal, very substantial legs, adjustable lower shelf and a very cool industrial chic look.

This was really a great buy! It’s right in the right place doing the right job!

Overall excellent with two issues. The top is not level with the legs fully inserted. It slopes to the left. The valves are also extremely hard to open and it hurts my wife's hands to try to turn them.

Me encantó la calidad del producto . Quedo perfecto para mi pequeño espacio .

really nice ez set up

was gonna put a mini fridge on top, i don't think so, nice very light load stainless table then, less than 10 lbs i think

-

Great little table! I did expect it to be a little bigger but that’s on me for not looking at the measurements. Super easy to build and is a strong clean looking table

Excellent stainless table for hobby use. Works well with a 3D printer. Best to bond the two piece legs together when assembling. Far more stable.

Works wish it had ignition system

I’ve been looking for a sturdy table for our laundry room and this was it. Easily holds heavy detergent boxes and much more